Видео

"...it seemed weird to put liquid soap in a soap dish..." Thank you. i needed a laugh!

Vase for your flours lol nice one

Years from now, when everyone has forgotten about covid, there's going to be some head scratching about that reference to paper towel shortage, lol!

Lol why is it sideways? 😂

LOL

What happened you have disappeared off RUclips again

I installed the provided FW where that he proved an it installed fine. However, something weird happed to the Z axis and I can't seem to fix it. No matter which direction turn the dial on the control box, the axis only goes in one direction, down and makes a horrible rough STEP motor sound. The Z wont go back up. I have to disengage the motors and manually back the Z axis up. Any suggestions?

Put a touch sensor on my biqu b1 and home is still bottom left. How come everyone elses auto homes to center.....

You saved me days of figuring it out. THANK YOU MAN <3

Thanks, now I can make a chicken nugget in the form of an Among Us character

Ive been fighting with my 3d printer for so long thank you so much

Hey! I am using a sony nex-5t and when I test to see if gphoto2 can capture the image, it gives me and error saying that my camera does not support generic capture. Any idea on how to fix this?

Thank you very much! I was stick after upgrading with cr touch + sprite pro. ❤ You are awesome!

My printer runs Marlin, but doesn't have this Z-offset setting in the Control/Motion menu.

Is there any link or something to the mystery box?

Which height difference between nozzle and probe? thanks

So would this work for me having a sprite extruder pro?

nope not helpful in fact i think i'm going to put my bl touch in the trash

Thank you for saving my day. I'm in troubles with the Z offset these days :D

How can I use vase mode with this

What kind of printer do you use?

Your video is a scam just like this printer is

This is how it starts. You all know it.

This video was super entertaining and is what brought me to your channel!

Why did you set the z offset too high by the thickness of some random piece of paper? The z offset is the height of the nozzle above the bed not the height of the nozzle above some random piece of paper lying on the bed. Use a feeler gauge of known thickness then subtract that thickness from the z offset you measure.

My z-offset resets to zero every time i restart the printer

Great tutorial! With a Sony A6400 I had some issues where gphoto2 couldn't save to SD, so I'm using gphoto2 --auto-detect --capture-image-and-download --filename="/home/pi/timelapse/photo-%Y-%m-%d-%H-%M-%S.%C". Also I had an issue where triggering the command directly from Octoprint wouldn't save the file, so I made a flask web server to run the command and then my custom gcode simply runs curl localhost:3000. Bit more complicated setup but it works perfectly.

Thanks! This was great!

How can i increase the travel speed when the head move to parking?

wish you show how you setup up the firmware

Why would you edit the full calibration, you cut the part I wanted to know about. Does the paper need to be pinned down (cannot move) or just touching? Does after it’s pinned down RDO you raise it .5 or .1 ?

C’mon bro. Give us a new one 😁

Solution for revo? Since obxidian is vapourware

GET OUT AND DO SOMETHING

haha a soapy men bar ... I'd visit that xD

Way off on the new version apparently.

It was common practice in the United States through the early 1900s to use lead pipes for interior plumbing. Since the 1930s, copper pipe has been used for residential plumbing. Until 1986, however, lead-based solder was used widely to join copper pipes. Lead-free solder and lead-free materials are now required by federal law for use in new household plumbing and for plumbing repairs. the amount of lead in a brass nozzle shouldnt be of any concern you breath in worse stuff just walking down the street

WHY ARE YOUR THUMBS SO WRONG

3

2

1

I'm sat here watching this great video with my newly delivered, 1st time ever, 3D printer. Plenty o assembly for me later. Loved that kitchen roll holder.

So when I do auto detect, the pi recognizes the camera….but when I run that -capture-image it fires back io library errors and can’t capture….

gphoto2--auto-detect does not exist....it is gphoto2_(space)--auto-detect

remember how people thought that the ole lockdowns were a good idea?

This method doesnt work with the Ender 5 pro and the latest marlin updates. Also doesnt consider BLTouch.

i hacked life i had her gift it to me for christmas so she would be mad ifever i didnt use it

This was a huge help! Saved me hours of time and frustration. Thanks!

Talking about the 3d printed plastics being porous and thus developing bacteria when used for food - I wonder if regular plastic bowls (sold in most supermarkets) have the same issue? ... and what about resin prints? I know resins used for 3d printing are toxic when liquid, but when cured they're not supposed to release particles, is that correct? And what about dental 3d resins?

Should the z offset be the same thicness as my feeler gauge?